IPCop-Forum.de

www.ipcop-forum.de


IPCop-Community
CL-Systems
Home Home   Doku Doku   Links Links   Downloads Downloads
UnIPCop Der (Un)IPCop   IFS IPCop-ForumSpy
CopTime CopTime   Galerie IPCop-Galerie   IPCop Userkarte Userkarte
Aktuelle Zeit: 29.06.2017, 16:16

Alle Zeiten sind UTC+02:00




Ein neues Thema erstellen  Auf das Thema antworten  [ 3 Beiträge ] 
Autor Nachricht
BeitragVerfasst: 13.03.2016, 11:14 
Offline
Rookie
Themenstarter
Rookie

Registriert: 01.05.2012
Beiträge: 4
Hello

I am trying to do a PXE boot installation on an Alix SBC with a CF card.
I have done this before with a Windoze laptop. That laptop has long gone.

I am now trying to use Ubuntu to do a new installation on a fresh CF card.

The problem I have is that I can see DHCP IP address offers being sent by the server in SYSLOG but these are not being accepted by the Alix board.

I have successfully connected the DHCP server to a Linux laptop client. I can see that the laptop is offered, and accepts the IP address.
On this basis, I am confident that I have a valid dmsmasq config.

After searching the internet, it seems that others have had this problem. It seems that some servers are not compatible with the Alix board.

Has anyone else had this problem with dmsmasq?
If so, is there a solution?


Nach oben
   
BeitragVerfasst: 22.03.2016, 10:38 
Offline
Apprentice
Apprentice

Registriert: 07.03.2016
Beiträge: 12
To: Admins, moderators, users with advanced technical knowledge:

Believe to provide a response to this new potential user asking in vain for help for more than NINE DAYS?

To you it seems courteous and well-mannered does not deigning to reply?


Nach oben
   
BeitragVerfasst: 10.01.2017, 10:44 
Offline
Rookie
Themenstarter
Rookie

Registriert: 01.05.2012
Beiträge: 4
Hello

Below is a working config file for DNSmasq. This file is specifically written to provide just enough functionality to initiate a pxeboot sequence.

Code:
# Configuration file for dnsmasq for IPCop Installation.
#
# This configuration file is exclusively intended for
# an IPCop installation onto a CF card.

#IPCop
# specify the wired Ethernet port.  Use the command ifconfig to find the ID.
interface=eth0

# ignore the wifi interface. Use the command iwconfig to find the ID.
except-interface=weth0

# Set the dhcp range, mask and lease time. 
dhcp-range=192.168.2.190,192.168.2.195,255.255.255.0,6h
.
# setup for pxeboot.  The IP address is the static IP address of the wired ethernet port.
dhcp-boot=pxelinux.0,pxeserver,192.168.2.200

#pxeboot setup.
pxe-service=x86PC,"Install Linux",pxelinux

#enable tftp server
enable-tftp

#declare tftp root directory
tftp-root=/srv/tftp

#disable DNS function
port=0

#avoids time delays
dhcp-authoritative

#test and log
log-dhcp


Nach oben
   
Beiträge der letzten Zeit anzeigen:  Sortiere nach  
Ein neues Thema erstellen  Auf das Thema antworten  [ 3 Beiträge ] 

Alle Zeiten sind UTC+02:00


Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 0 Gäste


Du darfst keine neuen Themen in diesem Forum erstellen.
Du darfst keine Antworten zu Themen in diesem Forum erstellen.
Du darfst deine Beiträge in diesem Forum nicht ändern.
Du darfst deine Beiträge in diesem Forum nicht löschen.

Suche nach:
Gehe zu Forum:  
cron
Powered by phpBB® Forum Software © phpBB Limited
Deutsche Übersetzung durch phpBB.de